Services

If you do not see what you want done, stop in and we will be more than happy to assist you in anyway that we can. We welcome all work and specialize in customization.

Service	Price
Per Man Hour	$70
Per Man + Machine Hour	$95
Minimum Charge Per Gun	$35
Written Cost Estimates	$40
Administrative Fee for Parts Orders	$15
Research fee for hard to find parts	$10
Clean and Oil Firearm Consists of completely stripping gun, cleaning all parts and checking for wear.	$60

If a firearm is dropped off for malfunction diagnosis, a magazine and at least 20 rounds of ammunition must be provided. If no ammunition is provided the cost of the ammunition used will be added to the cost.

We always recommend ordering your own parts, that way you know you will be getting exactly what you want. If you would like us to order the parts you must send us a link to the exact part you want. If the part you need is an original replacement then you do not need to send us a link. Any order totaling over $100 must be paid for before we will place the order.

Unless specifically stated, prices do not include the cost of parts.

Metal Finishing (does not include prep time)	Price
Wire Brush Stainless Pistol	$150
Wire Brush Stainless Rifle/Shotgun	$200
Bead Blast Handgun	$175
Bead Blast Rifle	$275
NitreBlue Small Parts for 1 Firearm	$130
Black Oxide Handgun	$175
Black Oxide Rifle/Shotgun	$200
Belgium Bluing Handgun	$300
Belgium Bluing Rifle/Shotgun	$350
Slow Rust Bluing Pistol	$500
Slow Rust Bluing Rifle/Shotgun	$600
Engine Turning Bolt	$90
Engine Turning Small parts	Hourly Rate

Sight Work	Price
Range Sight Firearm (does not include cost of ammo, targets, etc.)	$75
Bore Sight Firearm	$35
Drill and Tap Barrel or Receiver First Hole	$50
Drill and Tap Barrel or Receiver Each Additional Hole	$25
Install Dovetail Sight	$40
Install Front Sight Ramp Sweat-On Type	$80
Install Front Sight Ramp Screw-on Type (includes drilling & tapping)	$90
Install Front Sight Ramp Band Type	Hourly Rate
Install Insert in Pistol sight	$45
Install front/mid-rib shotgun bead	$50
Plug hole and re-drill for bead	$75
Install receiver sights Pre-Drilled and tapped (if not add cost of drilling & tapping)	$35
Scope Mounting Pre-Drilled and tapped (if not add cost of drilling & tapping)	$60

General Barrel and Action Work	Price
Check Headspace	$55
Remove stuck fired case from chamber	$50 and up
Remove live round from chamber	$100 and up
Remove obstruction from bore No Guarantee of Removal	Hourly Rate
Remove fouling from barrel	Hourly rate + materials
Lap Barrel	$100
Cut and crown Barrel - Basic Crown	$80
Cut and Crown Barrel - Competition Crown	$120
Install Pre-Threaded and chambered barrel	$150
Triggers (installation and adjustment) Shilen, Timney, Dayton-Traister, Moyer type...	$80
Single Set Triggers (installation and adjustment)	$120
Double Set Triggers (installation and adjustment)	$180
Install muzzle brake Pre-threaded barrel	$50
Install barrel band swivel	Hourly Rate

Shotgun Work	Price
Re-solder Rib (not including bluing)	Hourly Rate
Re-solder forend lug (not including bluing)	Hourly Rate
Raising Dent in Barrel (not including bluing)	$120 and up
Polish Chamber/Bore	$60
Port Barrel	$120
Refitting hinge pin lug	$300

Muzzle loader work	Price
Pull Ball No Guarantee of Removal	$40
Remove broken ramrod from barrel No Guarantee of Removal	$80
Stuck Breach Plug No Guarantee of Removal	$100

Revolver Work	Price
Chamfer Revolver Barrel	$40
Chamfer Revolver Cylinder	$80
Action Job (clean and smooth action)	$120
Rebarrel Revolver Remove old barrel, replace with new factory barrel	$140

Semi-Auto Pistol Work	Price
Action job (clean and smooth action)	$160
Install New Trigger	$60
Install Front Sight (using existing mount)	$30
Install Rear Sight (using existing mount)	$30

Stock Work	Price
Hunter finish - unfilled oil or lacquer finish on average stock (does not include any shaping)	$200
Gunsmith Finish (filled, rubbed oil finish on average stock) (does not include any shaping)	$250
Gunsmith hand rubbed High gloss Finish on average stock (does not include any shaping)	$350
Glass Bedding Barrel & Action Hunting Rifle	$120
Glass Bedding Barrel & Action Match Rifles, M-1 Garand, M1A1, etc.	$220
Glass Bedding Barrel & Action Pillar Bed	$220
Pillar Bed Receiver	$120
Install Recoil Pad	$70
Install Adjustable Butt Plate	$120

AR-15 Work	Price
Maintenance Rebuild Mil-spec parts Includes cleaning, new buffer spring & new gas rings	$100
Springs and Rings Maintenance Rebuild Mil-spec parts Includes cleaning + New upper and lower receiver springs, and gas rings	$150
Ultimate Maintenance Rebuild Mil-spec parts Includes cleaning + New firing pin, extractor, disconnector, disconnector spring, firing pin retainer pin, extractor pin, ejector roll pin, bolt gas rings, rear takedown pin .250", front pivot pin .250", trigger pin, takedown detent, selector detents, gas tube roll pin, trigger guard pin, bolt catch roll pin, forward assist pin, rear base spring pin, extractor spring, front sight spring, forward assist spring, magazine catch spring, buffer retainer spring, detent springs, selector spring, hammer spring, bolt catch spring, ejector spring and buffer tube spring.	$250
Install Aftermarket Trigger	$60
Install Aftermarket Forend/Free Float	$90
Assemble Complete Upper	$80
Assemble Complete Lower	$80
Assemble Complete Rifle	$150
Install Flash Hider on Pre-Threaded Barrel	$35
Install or Replace Gas Block	$60
Install or Replace Barrel	$80
Install or Replace Buttstock & Buffer Tube	$35

Other Services
Custom Machined Parts
General Machining
3D Printing
Prototype Design & Development

Granite State Armory - Full Service Gunsmith and Custom Machining

Granite State Armory - Full service Gunsmith and Custom Machining

Services

SERVICES

If you do not see what you want done, stop in and we will be more than happy to assist you in anyway that we can. We welcome all work and specialize in customization.

Unless specifically stated, prices do not include the cost of parts.